BERKO COLOUR LIGHT SIGNALS OO

Warranty - The warranty applies when the component is used in any reasonable application in conjunction with signal operation and control, and or point/turnout control or any similar or related model railway purposes, providing that it is installed with respect and has not been subjected to water or corrosive liquids, has been properly wired in accordance with instructions provided with the component plus any related online instructions as directed. Be operated within recommended supply voltages and power that has been supplied to it by a properly rectified power supply and or any NMRA compatible DCC decoder with a voltage and power output which meets the manufacturers specifications and that the correct polarity is observed. It is the customer’s responsibility to ensure that they have the necessary knowledge and skills to be able to correctly install the components purchased. Any damage caused to the component by the customer, is not covered by warranty.

ITEMS SHOWN BELOW ARE IN STOCK - MANY ITEMS HAVE BEEN OUT OF PRODUCTION FOR OVER 6 MONTHS and WILL NOT BE REPLACED.

WE ALSO OFFER ECKON , TRAIN-TECH & TRAINTRONICS SIGNALS

http://www.modeltrainsuk.co.uk/signal-kits-eckon-11-c.asp << Click

http://www.modeltrainsuk.co.uk/signals-traintronics-oo-30-c.asp <<Click

http://www.modeltrainsuk.co.uk/signals-berko-colour-light-oo-15-c.asp << Click

http://www.cravenmodels.com/TRAINTECH.htm << NEW RANGE OF SIGNALS

http://www.modeltrainsuk.co.uk/electrics-controls-switches-wires-22-c.asp << CLICK ELECTRICS CONTROLS SWITCHES

Unfortunately we will not be getting any new deliveries Tel 01588 660 580

PLEASE NOTE THAT THESE SIGNALS ARE POWERED BY 12 VOLTS DC SUPPLY ONLY. DO NOT USE ANY FORM OF AC POWER.

BERKO SIGNALS COME READY ASSEMBLED.

An Electrical power supply is required at 12 volts DC to illuminate the LED's which need to be operated with an appropriate switch. These items are not included in the kit.

Please read the instructions very carefully before attempting installation.

Special attention must be given to the operation of the LES's. DO NOT operate these items without a RESISTOR (included) in the circuit and then only with a 12 VOLT DIRECT CURRENT SUPPLY.

Children should be supervised at all times.

PLEASE DO NOT USE A HORNBY CONTROLLER FOR YOUR POWER SUPPLY - YOU NEED A SEPERATE 12 VOLT DC POWER SUPPLY ONLY.

.

IF AN ITEM IS NOT SHOWN BELOW IT IS CURRENTLY OUT OF STOCK

Which type of wire should I use where:

http://www.cravenmodels.com/MODELWIRES.htm << CLICK FOR ADVICE

IF AN ITEM IS NOT SHOWN BELOW IT IS CURRENTLY OUT OF STOCK
BUT PLEASE ASK 01588 660 580

POSTAGE AND PACKAGING - HOW IT IS CALCULATED
How our system calculates your P&P - £2.99 plus a small charge for each item which is shown on your invoice.
The more items that you purchase the higher the P&P cost becomes !
HOWEVER - PURCHASE 5 OR MORE ITEMS AND GET A P&P DISCOUNT !!!

OTHER MODEL RAILWAY SIGNALS AVAILABLE IN “N” GAUGE:

http://www.modeltrainsuk.co.uk/dapol-working-n-gauge-semaphore-signals-76-c.asp << click for DAPOL

http://www.modeltrainsuk.co.uk/signals-berko-n-plus-yard-lamp-kits-21-c.asp << click for BERKO

OTHER MODEL RAILWAY SIGNALS AVAILABLE IN “OO” GAUGE:
http://www.modeltrainsuk.co.uk/signals-berko-colour-light-oo-15-c.asp << click for BERKO

http://www.modeltrainsuk.co.uk/berko-eckon-model-railway-signal-spares-89-c.asp << click SIGNAL SPARES

http://www.modeltrainsuk.co.uk/berko-eckon-model-railway-signal-spares-89-c.asp << click for ECKON

http://www.modeltrainsuk.co.uk/train-tech-dcp-express-colour-light-signals-etc-97-c.asp << for Click Train-Tech

http://www.modeltrainsuk.co.uk/dapol-working-oo-gauge-semaphore-signals-75-c.asp << click for DAPOL

http://www.modeltrainsuk.co.uk/signals-traintronics-dcc-oo-30-c.asp << click for TRAINTRONICS